|
|
15005 Blossom Valley LN
El Cajon, CA 92021
contact@rmsrebar.com
(619) 390.1166 | Fax (619) 390.1165 |
RMS Rebar Fabricating Equipment has been the choice of the
Rebar Fabricating Industry for over 30 years.
The
RMS Shearline is a result of many years of experience in
both rebar fabrication techniques and equipment manufacturing.
RMS has built its reputation on providing the best equipment
available, at competitive prices, plus unmatched service
and support to customers around the world.
|
RMS (formerly
Arnold) Shearlines can be found at work in many of the leading rebar
fabrication shops, ranging from those whose volume is minimal to
some of the largest producers in the world. It is not uncommon to
find RMS Shearlines, built 10, 15 or even 20 years ago, still at
work... still producing day in and day out.
Every RMS Shearline is built to the most rigid standards, including
heavy duty components, a box channel frame, the heaviest kickoff
and bin arms and long lasting conveyor rolls. Low maintenance and
high, efficient performance are just some of the traits that make
the RMS system the choice of rebar fabricators of all sizes.
| |
|
| Heavy
duty parts and components are a trademark of RMS Shearlines,
including large diameter conveyor rolls, heavy steel kickoff
arms spaced at 24 inch centers, high capacity kickoff cylinders
and heavy bin arms. |
Bins
are spaced at designed intervals to maximize the storage of
various lengths of bundles. A higher passline provides greater
bin space, plus a steeper kickoff slope, assuring that bars
and bundles slide efficiently into the selected bin pocket. |
| |
|
| A
unique Short Bar Shearing Section, reduces much of the "manual
handling" of short bars. A mobile short bar bin system collects
short bars and easily moves away from the gauge table for tagging
and removal of the sheared material. Bin arms are air activated
and easily disconnected when bin section is moved. |
The
Preload Table is designed to allow the preparation of up to
two loads of steel ahead of the operator, even while the conveyor
is in use. Extra storage tiers are available on one or on both
sides of the conveyor. Independent Preload Controls permit the
"shakeout:" man to operate the entire table from his shakeout
platform. |
Micro
Technology, combined with Hands-On-Rebar Fabricating Experience,
Makes the RMS Shearline Control System User Friendly, Versatile
and Productive.
| |
|
| The
RMS 611 Hydraulic Guillotine Shear, used in conjunction with
the Shearline, represents a completely automated Shearing System.
The 611 Shear can substantially increase productivity while
reducing shearing costs compared with conventional shears. The
unique design of the 611 Shear makes it virtually impossible
for an operator to place fingers or hands anywhere near the
moving parts of the shear. |
The
RMS Shearline can be operated conventionally, or controlled
by computer software. Shown above, the Micro Control system
is ready to begin a "computer run," utilizing the Memory Box
system, that incorporates all of the shearing and setup data
required to complete the run. The Micro Control can also be
downloaded by a remotely located computer that transmits shearing
and setup data to the system, by hard wire. |
RMS
Rebar Shearline Specifications |
| Stock
Rack Capacity |
5
tons each side (with provisions for 5 more each side) |
| Number
of Standard Selectable Pockets |
48
or more |
| Pocket
Capacity |
up
to 80 tons |
| Standard
Bar Length |
up
to and including 70 feet (21 meters) |
| Standard
Bar Capacity |
#2
through #18 (6mm through 60 mm) |
| Conveyor
Rolls |
18"
wide x 6 5/8" O.D. (475 mm wide x 167 mm dia.) |
| Roll
Speed (Forward and Reverse) |
370
ft. per minute (113 meters per minute) |
| Air
Consumption At High Production |
25-35
CFM @ 100 to 120 psi |
| Electrical
Control to Pneumatics |
low
voltage 24V DC |
| System
Weight |
34,500
lbs. approx. (15,600 kg approx.) |
| Floor
Space (Double Side Bins) |
15
ft. x 135 ft. approx. (5 meters x 41.4 meters approx.) |
| Options
Available
-
Imperial or metric systems available.
- Right
or left hand flow available.
- Modular
design allows simple addition of many components, such as
foot stops, bin assemblies or conveyor sections.
- Single
station, toggle switch control available for less automatic
operation.
- Bin
interior, conveyor roll and kickoff arm protection available
for shearing epoxy bar.
-
Additional bins available (up to six bins per side).
-
Shearline can be used efficiently with virtually any shear.
- Additional
stock storage levels available to increase preload table
capacity to 20 or more tons.
|
To
watch a Shearline in action please click here
If you have trouble downloading the video please
go to:
http://www.apple.com/quicktime/download/
and download the "FREE Quicktime Player"
|
